The LS type screw conveyor is a new type of conveying device for continuously conveying powder and granular objects in a closed circular cross-section housing by means of a rotating spiral. The head and tail bearings are moved to the outside of the casing. The sling bearing adopts sliding bearing and is equipped with dust-proof sealing device. The whole machine has high reliability, long service life, strong adaptability, convenient installation and maintenance, and flexible arrangement of in...
Used for filtering and removing impurities from liquids. Working principle: After the untreated suspension is sent to the filter cartridge, solid phase particles larger than the outer diameter of the small hole on the filter cartridge are retained by the filter cartridge and sent to the bottom of the filter by a rotating brush. The filtered liquid is sent out from the liquid discharge pipe, and the filtered impurities can be discharged with the liquid flow through the impurity overflow valve ...
The advantages of the spray type sulfur tower over the traditional ceramic sulfur tower, spray type sulfur tower and glass fiber reinforced plastic absorption tower are mainly reflected in the following aspects:
1. The spray type sulfur tower is easy to operate, and the produced sulfurous acid concentration is stable, which reduces the odor of so2 and reduces environmental pollution.
2. The spray type sulfur tower is easy to repair and maintain. If the effect is good, there is no maintenance...
Technical parameters
Type
Separation cylinder diameter(mm)
Production capacity commodity corn(t/d)
Feed pressure(Mpa)
Recoil pressure(Mpa)
Dimensions(mm)
SPX-360
360
150
0.1
0.1
580×430×1520
SPX-450
450
300
0.2
0.2
1129×970×2538
SPX-750
750
500
0.25
0.25
1200×900×2730
SPX-1000
1000
1600
0.35
0.35
1500×1150×3420
Anyone who pumps liquid for any purpose (irrigation, industrial, or private and public water systems) knows their greatest enemy is sand, silt, grit or other s...
Main feature
◎ Manufactured using international quality standards.
◎ Advanced lubrication system: low power, low energy consumption, small fuel consumption, low use cost.
◎ Water-cooled device improves the operating temperature of the bearing and increases the service life.
◎ Supported by a certain flexible bearing seat, the equipment has less vibration and more stable operation.
◎ Adopt 5V united belt automatic tensioning device, high transmission efficiency, stable and reliable operation, l...
The dual-shaft mixer is also known as a wet and dry mixer. The materials in the machine are subjected to compound motion by two rotors in opposite directions. The paddles with animal material rotate counterclockwise along the inner wall of the machine slot, and the animal material is turned left and right. A weightless area is formed at the intersection of the two rotors. In this area, regardless of the shape, size and density of the material, the material can be floated in an instant weightl...
The air dryer uses high-speed hot air to suspend the mud-like, powdery and granular materials in the air. Large heat transfer surface area, high heat transfer coefficient, short drying time (most materials only need a few seconds to dry), suitable for drying heat-sensitive materials. This equipment is widely used in the drying of powdery and granular materials in food, chemical, pharmaceutical, building materials and other industries. The products that have been used in this series of dryers ...
In order to obtain the required efficiency, degermination is carried out in two stages, each stage consisting of two separation passes.
Working principle
The starch slurry containing cracked steeped corn and germ is fed tangentially into the first pass cyclone with sufficient velocity to create a vortex action forcing the slurry into a spiral. As the rapidly rotating flow spins about the axis of the cone, the lighter germ fraction is forced to spiral inward and out through a centrally located...
Working Principle
After a grinding process of the socked corn, the crushed corn pieces will fall into the grinding chamber through the inlet under the action of gravity, and then be thrown to the fixed and moving discs. Since the relative rotation of the 2 discs and the special layout of discs, the corn particles will bear a centrifugal force and be thrown out of the discs. In this process, the corn kernels rub and hit with each other to get crushed. While the mutual impact between the partic...
Pressure curved sieve is one of the most advanced starch equipment at home and abroad. The pressure curved sieve is screened by multi-access counter current washing process, which can effectively improve the powder yield and starch quality, has significant economic benefits.
Echnical parameters
No.
Item
Single Unit
Duplex
1
Screen surface arc angle
120°
120°
2
Screen surface width
50um/75um/100um/120um
50um/75um/100um/120um
3
Material handling capacity
42-57m³/h
85-115m³/h
4
Feed p...
This device is made of motor, reduction gears, draught fan, drying tube and shell body.
Working principle
Steam heat drying tube at first, material get into shell body, drying tube rotated by motor, meanwhile, stir fry and push materials, the wet steam will be discharged to outdoor by draught fan.
Equipment characteristic
1. Advantages: low steam consumption, low electricity consumption, wide range of drying material, large output, large water evaporation, high moisture material which can d...
In order to obtain the required efficiency, degermination is carried out in two stages, each stage consisting of two separation passes.
Working principle
The starch slurry containing cracked steeped corn and germ is fed tangentially into the first pass cyclone with sufficient velocity to create a vortex action forcing the slurry into a spiral. As the rapidly rotating flow spins about the axis of the cone, the lighter germ fraction is forced to spiral inward and out through a centrally located...